How do I build a wind turbine with free instructions on how to safely use it? - free instructions for a wooden swing set
I mean reduce the power consumption by trying to go to sun), but have limited resources (money and knowledge. I would have free plans and instructions on building and simple procedures for the maintenance, care and use of the system. I need to follow safety measures to implement this system. I have no mechanical background, so I have to put it simply, so you understand what I am doing.
Wednesday, February 3, 2010
Free Instructions For A Wooden Swing Set How Do I Build A Wind Turbine With Free Instructions On How To Safely Use It?
Subscribe to:
Post Comments (Atom)
3 comments:
Visit save just a few yards and buy a used car alternator (any make or model runs) and then plug it saved into a prop from an airplane. Thats a can be easily damaged, are not effective or safe enough for the flight would be perfect. Then go with a roller or generator, and charging the use of this system to the car battery 12 volts. Then connect the battery to "investor in Wal Mart, to buy, etc., and will run backwards for your computer or TV or whatever free-wind!
At first I did on Google, but everyone was complicated by the source, so I made mine.
1. get som 2 inch x 2 inch and cut to about five meters.
2. Now for a little head [30 "] (turns into the wind)
3. get a 15mm screw that is 15cm long
4. Long drill a hole of 20 mm, which is 10 cm long
5. Cut a piece (20 mm) copper tube and you will find a coin that are in (less than 5p fits).
6. Slide the copper pipes and coins in the hole.
7. Now get Plyboards 10mm (6 "x 6")
8. old to obtain a driver of a dishwasher or washing machine (go to the local landfill or on ebay for one year)
9. You cross the belt and hold the 6x6 (the tree at the end) should
10. Part of the layer clipping anothe (3 "x 3")
11. a hole in the the same size as the pin --
12. Drill a hole in the screw (it should go straight through)
13. Dill a hole through the pines Longitudinal --
14. put a screw into the hole and pin layer
15. now do the same as 12, but we are at 90 degrees to the right and through the first drill holes, of which only half
16. Now do the same as 13 but 90 degrees Bachelor
17. put a screw through the holes of 2 new
18 for 2 pieces of 1 inch x 1 inch (50 cm long) and to reduce the length of 2 inches coner to corner.
19. Screw two 3x3 layers [of the work should be put in the opposite direction.
20. Cut 2 pieces 30 cm x 5 cm masonite
21. to 1 inch x 1 inch or products that it will be at 90 degrees to each other attatched
22. Throughthe Center put the lock on the pice of the operation of the motor layer [the lock against the blade by tightening a thin layer of 2 inches square hardboard, covered head bolt]
23. Now place the screw in the 30-inch piece of 2x2
24. Also, the layered piece of propeller, with preventing the motor part of 2x2 to 30 inches, this amounts to avoid slipping.
25. Well, to go online to get a piece of paper or hardboard 15x15in
26. attatched is the head ofYour engine
27. Screw slot in the copper tube [slot 2 "x 2"]
He now has a wind
ps. IM afraid, I'm only water feature fuel Avery so I do not know much about the electrical system.
SECURITY
To get the most out of this generator, I recommend counting on the highest side of his house.
BUT
1. ensure that their widows in the vicinity
2. lay well, you do not wan't to fall out of his house and kill someone
3. Just use your common sense
I hope that was a little help.
Would you like wind or solar power? In any case, cheap solar cells to obtain because they are really expensive to get started. Windmills are a bit unpredictable in their reliability. And you need a converter that can pass a windmill at the public power, when it received no wind. It's a great thing, and you really do not save much money anyway.
Post a Comment